Diy magic mirror tutorial install#
Diy magic mirror tutorial software#
Diy magic mirror tutorial code#
Diy magic mirror tutorial tv#

When you're staining the vertical services, try to get a smooth line and avoid drips. You don't need to push excessively hard, but try to work it into the wood. Dip the material into the stain and let it absorb thoroughly. The most efficient way to apply a stain is to wipe it on, which is why we recommend old socks or a t-shirt. Start by opening the can and stirring the contents. Usually, you'll see a wipe off time and a restain time, take note of those. To stain your frame, doublecheck the directions of your stain for drying times. You can skip sanding any section that won't be visible. Try to find any areas you missed and sand as needed.ĭon't forget to sand the inside border of your frame, where your monitor will show. You should feel a noticeable difference where you've sanded. If you're painting or you want a deeper stain color, skip the 220 grit paper.Īfter sanding, run your hands along the wood. Start with the 80 grit sandpaper, then move to the 120, then the 220. When the lines are gone, you've probably sanded enough. Tip: If you're new to sanding, try drawing wavy lines on your frame as seen in the picture above. As much as possible, sand with the grain of the wood (that is, follow the lines you see in the wood), and don't push with all your might.

If you're new to sanding, the process is pretty straight forward. If you skip this step, stain and paint will only highlight the imperfections. Sanding your wood removes splinters, dings, and other blemishes the building process created. How much wood and how wide depends on your monitor (see more in building the frame.)īefore you stain or paint wood, you need to sand it properly. You'll also want something thin like plywood to make the back of the box if you aren't hanging the frame. Wood to build the frame and box: We recommend hardwood like Maple or Walnut at least one inch thick.Add a vapor filter if you're applying polyurethane without ventilation. A ruler or other straight edge (for drawing straight lines).A miter saw (or handsaw and protractor).Sandpaper in 80, 120, and 220 grit (omit 220 if you decide to paint).Wood filler (if staining, get stainable wood filler).The product we linked on Amazon is a generic size, but we had good luck ordering from a local glass supplier. Two-way Glass: Your glass should be a little larger than the dimensions of your monitor.It's also helpful (but not necessary) to remove the frame from the monitor. Something thinner and lighter is better, but this monitor by Sceptre would work. A monitor: Preferably at least 24 inches, and one you don't care about losing.To get started you'll need the following: If you have a friend who owns some, ask if you can borrow them. And remember, you don't have to buy the tools. But because we had everything on hand except the glass and wood, we only spent $140. If you bought every item in the following list, you'd spend around $700. You'll spend about three to five hours actively working on the frame and installing the software.ĭepending on what you already have, this project can either be inexpensive or expensive. The longest parts are passive, like waiting for glue and stain to dry.

Diy magic mirror tutorial code#

But even someone with little to no experience with woodworking and code can build this DIY project with a bit of patience in a weekend or two.

Diy magic mirror tutorial software#

The harder parts are creating the frame box, setting up the Raspberry Pi, and then customizing the software to show your preferred information. Installing the software is easy-it requires just one line of code. Once installed, you can customize it to show your calendar, weather, news, and more. Michael and other contributors have created an open-source Magic Mirror platform you can install.

Diy magic mirror tutorial tv#

Inside the box, you'll place one-way glass (often seen on TV in police dramas), a monitor, a Raspberry Pi, and the cables necessary to power your setup. The idea is pretty simple you'll build a frame and box.

Diy magic mirror tutorial install#

Update the package manager, and install the NTP client: opkg updateĬonfigure the NTP client: vi /etc/ntp.confįind the line that says 'server 127.127.1.0' and change it to (press 'i' to edit): server mirrors have been around awhile, and the most prominent version comes from Michael Teeuw.

Press 'esc', and enter ':wq' to save and exit. Press 'i' to start typing, and enter the following: src/gz all Open the package manager file with: vi /etc/opkg/nf To do that, we will rely on an NTP service to regularly poll an Internet-connected server for the most accurate time. We will want our Edison system time to be up-to-date. Luckily, we can install it through npm: cd ~ That does mean we need to install a few more dependencies, though. With the UPM modules installed, we can work on writing the actual code.